Water Well & Pump Service FAQs

Pittman Well Boring provides water well and pump services for residential and commercial properties. Before publishing, confirm the exact service list, including well boring or drilling, pump installation and repair, pressure tank service, inspections, water testing, and emergency service.

Common signs include low or inconsistent pressure, no water, air sputtering from fixtures, frequent cycling, increased electricity use, or unusual system noises. A diagnostic inspection can identify whether the problem involves the pump, tank, controls, plumbing, or well yield.

A loss of water can result from a tripped breaker, electrical fault, failed pressure switch, pump problem, plumbing leak, frozen pipe, or low water level. Check the breaker and visible plumbing, then contact a qualified well professional if service does not return.

Pump life varies based on pump type, installation quality, water chemistry, usage, system sizing, and maintenance. Have the system evaluated when performance changes or repairs become frequent.

Low pressure may be caused by a weak pump, pressure tank or switch problems, clogged filters, mineral buildup, plumbing leaks, undersized equipment, or declining well production. A pressure and flow evaluation can isolate the cause.

Repair may make sense when the pump is relatively new and the problem is limited to a replaceable component. Replacement may be more cost-effective when the pump is significantly worn, repeatedly fails, is improperly sized, or has major damage.

Routine inspections help identify changes in pressure, pump cycling, tank condition, electrical controls, the well cap, and visible plumbing. The appropriate schedule depends on the system, local requirements, water conditions, and manufacturer guidance.

Testing frequency depends on local health guidance and property conditions. Testing is especially important after flooding, repairs, changes in taste, odor, or appearance, a nearby contamination event, or when buying a home with a private well.

A pressure tank stores water under pressure and helps provide steady flow between pump cycles. Correct air charge and tank sizing reduce short cycling, protect the pump, and support consistent pressure.

Rapid pump cycling, fluctuating pressure, reduced drawdown, visible corrosion, water at the air valve, or a waterlogged sound can indicate a pressure tank problem.

Well depth depends on local geology, groundwater conditions, construction standards, and the depth required to reach a reliable water-bearing formation. A qualified contractor evaluates site conditions before recommending a design.

The timeline depends on the service, site access, permitting, ground conditions, equipment availability, testing, and weather. A site-specific evaluation provides the most accurate schedule.

A new well may be considered when the existing well has persistent yield problems, structural failure, recurring contamination, unrecoverable damage, or repair costs that no longer make sense.

Sometimes. Options may include well rehabilitation, pump adjustments, deepening, hydrofracturing, correcting leaks, or adding water storage. The right solution depends on well construction and local geology.

Hydrofracturing uses pressurized water to open or clean existing fractures in bedrock near a drilled well. It may improve groundwater flow in suitable formations, but results depend on geology, construction, and site conditions.

Changes may be related to iron, manganese, sulfur compounds, sediment, bacteria, plumbing materials, treatment equipment, or other water-quality conditions. Laboratory testing should identify the cause before treatment is selected.

Yes. Floodwater and runoff can introduce sediment or contaminants through a damaged or poorly sealed wellhead. Follow local health guidance for testing, disinfection, and safe use after flooding.

Private well water can be safe when the well is properly constructed, protected, maintained, and tested. Routine laboratory testing and prompt attention to changes are important.

Check the electrical panel for a tripped breaker and confirm whether the outage affects the entire property. Do not open electrical controls or attempt unsafe repairs. If power returns but water does not, call a qualified professional.

A properly constructed well can remain usable for many years, but lifespan varies with construction, geology, water chemistry, maintenance, casing condition, and groundwater changes. Pumps, tanks, and controls typically require service sooner.

Contact Pittman Well Boring to confirm emergency availability, service hours, response area, and after-hours policies. Replace this answer with the company’s approved details before publication.

A leak, failed pressure tank, switch issue, low well yield, or worn pump may cause continuous operation.

Call for no water, persistent low pressure, rapid cycling, leaks, unusual noise, discolored water, or a sudden change in taste or odor.

A failed or incorrectly charged pressure tank can cause frequent cycling, placing added wear on the pump and controls.

Testing may be appropriate after repairs, disinfection, flooding, or any change that could affect water quality.